生態護坡護岸模具的生產過程就是需要將提前準備好的水泥或者是混凝土進行攪拌，在攪拌的過程中需要經常加入清水，保證材料攪拌到泥漿的狀態，但是需要注意的就是清水的比例，不能夠讓泥漿的攪拌過于稀釋，之后在將攪拌好的泥漿澆筑到生態護坡護岸模具中進行震動，震動的處理主要就是需要將泥漿中的氣泡排干凈，氣泡的存在不僅僅會影響到整塊的護坡磚硬度的問題，如果氣泡凝固在表面位置的話也會造成護坡磚預制件的美觀性下降，出現其中一個問題的話，這個護坡磚預制件就不能夠在工程中正常使用了，震動要等到里面的泥漿達到一定的程度再去進行晾曬，大多數的拆模都是需要將生態護坡護岸模具拆開，然后再去取出制作好的護坡磚預制件才可以，因?yàn)樵摲N模具是能夠拆卸的，所以制作出來的護坡磚會更加的完整光滑，可以大批量的在工程中進行使用操作，而且生態護坡護岸模具的拼接和拆卸式需要經過螺栓和其他零件的配合，這樣能夠保證模具的密封性，不會在生產的時候出現漏漿的意外情況，影響到模具的正常生產處理。

he production process of ecological revetment and revetment mould is to mix the cement or concrete prepared in advance. During the mixing process, clear water is often added to ensure that the materials are mixed to the state of slurry. However, it is necessary to pay attention to the proportion of clear water, which can not make the slurry too diluted. After that, the mixed slurry is poured into the ecological revetment and revetment mould The treatment of vibration is mainly to remove the bubbles in the mud. The existence of bubbles will not only affect the hardness of the whole slope protection brick, but also cause the beauty of the prefabricated parts of the slope protection brick to decline if the bubbles solidify on the surface. If one of the problems occurs, the prefabricated parts of the slope protection brick cannot be used normally in the project. Vibration It is necessary to wait until the mud inside reaches a certain degree to air and dry. Most of the formwork removal needs to take apart the ecological revetment and revetment mould, and then take out the prefabricated parts of the manufactured revetment bricks. Because this kind of mould can be removed, the manufactured revetment bricks will be more complete and smooth, and can be used in large quantities in the project The splicing and disassembling of the ecological revetment and revetment mould need to be matched by bolts and other parts, so as to ensure the sealing of the mould, avoid the unexpected situation of slurry leakage during production, and affect the normal production and processing of the mould.